Rotary SPO10-RA-TRIO-SW 10,000 lb Symmetric — 2-Post Car Lift

About this 2 post car lift

The Rotary SPO10-RA-TRIO-SW is a 10000-lb capacity 2 post car lift positioned in Rotary's lift line for buyers who need a lift that matches specific bay constraints — not a generic recommendation. The specs, the ordering flow, and the guidance below are here so you can make the pick with real numbers instead of marketing copy.

Who this 2 post car lift is built for

10,000 lb is the workhorse 2 post car lift capacity for independent shops and serious home garages — handles nearly every passenger vehicle plus most half-ton pickups.

Install requirements — matches base configuration

Rotary SPO10-RA-TRIO-SW is a factory-configured variant of a base model in this brand's 2 post car lift line. Install requirements — ceiling clearance, concrete thickness and PSI, electrical draw, ALI certification, warranty — match the base configuration published on that model's product page. If you're comparing this specific 2 post car lift variant against your bay, text (833) 736-7290 with your bay measurements and we'll confirm which base spec sheet applies before you order.

The specs on this 2 post car lift come from the manufacturer's install and operation manual — never a marketing brochure. That's how we vet every 2 post car lift on the site, whether it's a base model or a factory variant, so the numbers you see always match what's in the crate.

About the manufacturer

Rotary Lift, part of Vehicle Service Group, has been building automotive lifts in Indiana since 1925 — the oldest continuously operating vehicle-lift brand in the United States. Rotary's SPO series 2 post car lifts are the benchmark independent shops replace their tired 20-year-old lifts with when they finally break down. Cable/sheave systems are engineered for high-cycle commercial use.

On our three-tier framework, this 2 post car lift sits in our commercial tier — priced and engineered for that use case, warranted accordingly, and stocked because we've seen the brand hold up in the field.

Ordering, freight, and financing

The Rotary SPO10-RA-TRIO-SW 2 post car lift ships freight from the manufacturer's regional warehouse in 3–5 business days after order. Freight is free anywhere in the 48 contiguous states — the shipping cost is already built into the price you see on this page. Alaska, Hawaii, and international buyers should call for a freight quote before ordering.

Financing is available at 0% APR for 12 months with a 90-day deferred first payment through First Business, our lending partner for equipment purchases. The application is short, the approval usually comes back the same day, and there's no cost added to the price of the 2 post car lift for taking financing — the interest rate really is zero for the first 12 months.

Every purchase is backed by the manufacturer's warranty, plus our own return policy on the crate condition at delivery. Inspect the pallet before signing the freight receipt.

Bay preparation checklist before your 2 post car lift arrives

The install goes fast when the bay is ready. Here's what to have squared away before the freight truck shows up with the Rotary SPO10-RA-TRIO-SW pallet — most of it takes an hour or two of prep and saves days of rework:

• Concrete verified against the base spec. This 2 post car lift is a factory variant — pull the base model's install manual and verify your slab thickness and PSI against those numbers before drilling.
• Ceiling clear point measured. Not just the ceiling — the lowest point in the swing arc: HVAC ducts, garage-door tracks, light fixtures, joist bottoms. Check against the base model's minimum ceiling spec.
• Anchor locations laid out. Mark where the columns will land. Confirm no plumbing, floor heat, or electrical conduit under those locations before drilling.
• Dedicated electrical circuit run. This 2 post car lift needs a dedicated single-phase circuit landed within reach of the power-side column — verify voltage and amperage against the base spec.
• Two people scheduled for install day. A 2 post car lift install is doable solo but faster and safer with a second set of hands for column raising and cross-tube alignment.
• Torque wrench and hammer drill on hand. The install manual specifies anchor bolt torque values — a click-type torque wrench is not optional. A 1" SDS-Max hammer drill will chew through concrete anchor holes in a fraction of the time of a rotary hammer.

Text the base spec sheet (or your bay measurements) to (833) 736-7290 and we'll confirm the install requirements for this specific 2 post car lift before you order.

Not sure the Rotary SPO10-RA-TRIO-SW will fit your bay?

This is the single most common reason people return a 2 post car lift after freight delivery — the ceiling isn't tall enough, the slab is too thin, or the electrical service can't handle the draw. All three are easy to catch before you order.

Text a photo of your bay to (833) 736-7290. Include a shot of the ceiling from floor level (so we can see joists, HVAC ducts, garage-door tracks), a shot of any exposed slab edges, and a photo of your electrical panel. We'll cross-check the install manual for this specific 2 post car lift against what you send and get back to you — usually the same day, always free, no obligation to buy.

If your bay checks out, we'll help you complete the order. If it doesn't, we'll tell you which model in the same brand family would fit, or whether the fix (raising the ceiling clear point, pouring a slab overlay, adding a subpanel) is worth it before ordering any 2 post car lift.